A Lectra MTK kit is a maintenance kit: one box that holds the wear parts a technician needs for a scheduled service on a specific Vector model. Instead of ordering parts one by one and hoping nothing is missing, the kit is matched to the machine and its service interval. You replace it when the machine reaches that interval, or earlier if the parts inside show wear before then.
Key Takeaways
- An MTK kit groups the wear parts for one scheduled service on one machine model.
- Kits are matched to the machine version and the service interval, so a kit for one model will not fit every Vector.
- Typical contents are wear parts around the knife head, sharpener and cutting surface; exact contents depend on the model.
- Follow the service interval, but replace early if the parts show the wear signs described below.
- Compatible kits can be built to a standard list or to your own maintenance plan.
What Is an MTK Kit?
Lectra maintenance is planned around regular kit replacement. Every cutter has parts that wear in proportion to how much it cuts: parts that guide and drive the blade, parts that keep it sharp, and parts that support the material. Replacing them together, on a schedule, is faster than chasing them one at a time, and it keeps the machine from stopping because a single small part ran out.
A kit turns that schedule into one order. The technician opens one box, works through the service and closes the job without a second trip to the stores.
How Do You Read an MTK Kit Name?
Kit names carry the information you need to match them. On our own listings, for example, a kit named MTK 4000H VT-FA-Q80 is a kit for the Vector Q80, and MTK 4000H VT-AU-iX9 is a kit for the iX9. The 4000H part of the name refers to the service interval in operating hours.
Two kits for the same model can differ by version or configuration. Some names carry a note such as “without DWV”, which tells you a component is left out for machines that do not use it. Always match the kit to the nameplate on your cutter, not only to the model family.
What Is Typically Inside?
The exact list depends on the machine and the interval, but kits are built around the parts that wear fastest. Typical contents can include:
- Sharpening belts or grinding stones for the sharpener.
- Guide parts that keep the blade on line.
- Bearings and other rotating parts around the knife head.
- Seals and small wear parts.
- Fasteners needed to complete the service.
Consumables such as blades and bristle blocks are often ordered separately, because their usage depends far more on what you cut than on running hours. Ask for the full packing list before you order, so you know exactly what is in the box and what is not.
When Should You Replace the Kit?
The service interval is the starting point. When the machine reaches it, the kit is due. But intervals assume typical use, and many cutting rooms are not typical. Replace earlier if you notice:
- Cut quality dropping on the bottom plies, even with a fresh blade.
- The blade wandering or vibrating more than usual.
- Noise from the knife head that was not there before.
- Sharpening taking longer, or the edge not lasting between cycles.
- Visible play in guides or bearings during inspection.
Heavy, abrasive or technical materials, long shifts and high cutting speeds all shorten the real interval. If you consistently see these signs before the scheduled service, plan the next kit earlier.
Standard Kit or Custom Kit?
| Standard kit | Custom kit | |
|---|---|---|
| Contents | Fixed list for the model and interval | Built from your own parts list |
| Best for | Following the planned service | Your own maintenance plan or mixed fleets |
| Changes | Parts can be added or removed on request | Every line is your choice |
| Packing | Standard labeling | Your labeling and carton requirements |
Many service companies and larger cutting rooms run a custom kit: the standard parts plus the consumables they always need, packed together so one order covers the whole service.
How Should You Store Spare Kits?
Keep kits sealed until use, in a dry place away from heat. Abrasive belts and rubber parts age faster in humid or hot storage. Label each kit with the machine it belongs to, especially if you run several Vector models, so the right box goes to the right cutter.
Compatible MTK Kits From PeiParts
We assemble compatible MTK kits for Vector iQ, iX, MH / MP / M88, iP and earlier Vector models, with every part labeled by reference number. You can order a standard kit or send us your own parts list, and distributors can order kits under their own brand. See Lectra MTK Kits for details, or browse kits on our In Stock page.
Get an MTK Kit Quote
Tell us your machine model and service interval, or send your parts list. We reply within 12 hours.
